Comment Feed for Channel 9 - Coding4Fun Cannon – Building the Robot http://ecn.channel9.msdn.com/o9/c4f/images/10000413_100.jpg Channel 9 - Coding4Fun Cannon – Building the Robot We have a chicken or egg issue here. Do we talk about how to build the robot, or about the software needed to run it? Since the hardware choices directly determine how the software will be developed, we have to think about how to make the robot safe and at the same time functional. No one wants a 100lb robo We have a chicken or egg issue here. Do we talk about how to build the robot, or about the software needed to run it? Since the hardware choices directly determine how the software will be developed, we have to think about how to make the robot safe and at the same time functional. No one wants a 100lb robot with a pressurized co2 tank and armed t-shirt cannons running wild. This article won’t really talk about code, since that is a different, upcoming article; rather, this article will explain how to build the physical robot, code-named Betty. To find out about the Windows Phone 7 application, code-named Frank, wait for the next article. Clint Rutkas - Microsoft Coding4Fun Ninja Source Code: Download Difficulty: Software Medium - Hardware Advanced Time Required: 2 weeks Software Needed: Visual C# 2010 Express, Visual Studio Phone Developer Express Hardware: Servo City Pan-Tilt, Robot Marketplace battlebot kit, Phidget 0/0/4 Relay board, Phidget Advance Servo controller, t-shirt cannons, nuts and bolts, polycarbonate, and a lot of coffee / soda. WARNING: This project deals with voltages and amperages that could hurt you and your electronics. Use voltmeters and common sense before randomly connecting and touching wires. In this multipart article series, we’ll cover: Project overview Developing the phone application Building the robot Creating the phone user experience Part 9c into Part 143B? What? For a project like this, there are no real instructions. It is a custom project. If I was asked to build another one, chances are it would look different. I spent a lot of time drawing out and talking to people, figuring out how to get all the parts to play nicely. Only then did I go down to my local plastics place (I recommend TAPs Plastic in Seattle) to give them a technical drawing of what I wanted. The parts will vary depending on the look / feel you want. I wish I could give you part drawings that you could replicate, but I don’t think they would do you much good. What I will do, however, is give you a ton of pictures, which should point you in the right direction. Research and development Typically, I research parts and features to death. However, due to the two-week time constraint of being ready for the Mix conference, I went with what I knew worked for my previous projects while focusing on how to make Betty self-contained since requiring Betty to be plugged in would defeat the purpose of having her be a robot. The design of Betty was broken down into a few key parts: driving, aiming, shooting, brains, and power. Primary part list: 1x – Battlekit medium kit with stock batteries 1x – Cisco Linksys gigabit wireless router 1x – 13” HP Envy laptop 1x – Phidget 0/0/4 Relay board 1x – Phidget Advanced Servo Controller 1x – Servo City Pan-Tilt 985 series 2x – Burst 175 T-Shirt cannons (with electronic solenoid values) 2x – Odyssey PC680MJ 12V 17AH Batteries 2x – Castle BECs (set to 6V) (Battery Elimination Circuit) 1x – Castle Pro BECs (set to 12V, has two outputs) 1x – 10lb CO2 tank 1x – Pressure valve (Able to adjust to 300 PSI) 1x – Serial port to USB Adapter Driving a robot Without knowing the weight of certain parts, I had to choose a base that could handle the load and be big enough to support everything I loaded onto Betty. From building random, previous robots, I knew of a company, Robot Marketplace, with a ton of internet parts, including full bodies. I decided a medium version complete with stock batteries and motors would fit my needs. The batteries are configured here in series to boost the voltage from 12volt to 24volt. The kit comes with an AmpFlow motor controller, which is actually a rebranded Roboteq controller. This connects to the computer via a serial to USB adapter. You’ll also have to get the Roboteq software to configure the motor controller to work off RS232 (Serial Port). Shooting and aiming a t-shirt cannon The cannons are Burst 175 T-Shirt cannons with electronic solenoid valves, allowing them to be fired with the Phidget 0/0/4 Relay board. The cannons are mounted onto a Servo City Pan-Tilt which is controlled by a Phidget Advanced Servo Controller. The pressure on the robot is fixed. Having a brain and communicating Since Dan and myself had features in the initial planning that could require heavy processing, we decided it was best to have a laptop control everything, though initially, ideas of using the .Net Micro-framework were put out there as well. We decided on a 13” HP Envy to be the brains of the operation. One thing we loved about this laptop is the extended battery, which snaps onto the bottom to give it a 14-hour life! We used a Linksys wireless router for getting the phone and the laptop to be able to talk to one another. For the keynote, we had to leverage a wired connection, but we’ll typically use a wireless connection between Betty and Frank. Powering everything The battlebot kit comes with batteries to power the motors, but we still needed to power everything else. I went with 2 massive 12volt 17-amp hour batteries, which just barely fit the case, and I wired them in series to boost the voltage. This would give me the massive amount of energy needed to power all of the random electronics. Since nothing on this robot, other than the motors, runs at 24v, we adjusted the voltage. This is where the BEC (Battery Elimination Circuit) came into play. Here is the breakdown: If you use different parts, you’ll have to pay attention to the voltages. This is one reason why I like the Castle BEC units, I could just alter the voltage instead of buying a new BEC. I also highly recommend installing on/off switches. If you plug stuff in with this type of voltage, you’ll get sparks, which carbonize the plugs. Building knowledge brain dump To mount the top of the robot to the chassis, I had to get a drill press and drill the sidewall of the front and back plate. I decided to save some money and buy a low-end drill press for this, but having a higher end drill press would have made my life a bit less stressful. Drilling it had 1/16th of an inch on either side to punch through. After drilling, I used a 10-24 tap to put in screw threads so I could use thumbscrews to mount the two together. The two plates were T-6 aluminum, so I used WD-40 to help lubricate both drilling and tapping. If you’ve never tapped a hole before, make sure you go a half turn in and then a quarter turn out. This helps break up the little bits of metal in the hole and so helps prevent the tap from breaking. One thing to be aware of is the movement of the Pan-Tilt and how this relates to mounting the cannons. We had programmatic stops so the cannons didn’t go too far up or down or rip out any cords by rotating too much. Another helpful tip is to use extra wire so you can move stuff around. Then, once you figure out final layout, either trim the extra wire or install entirely new wiring. My final tip, and the tip to follow if you only follow one, is the following: use a Voltmeter before you connect anything together. I failed to follow this advice and had two wires switched, which reversed the polarity of the power. When I turned it on, I had a nice electrical fire break out, which destroyed 3 BECs. This was a hundred dollar mistake, which took a half-day to repair, and it could have been far worse. Verifying and re-verifying the voltage will not only keep you safe, it will keep you from having to buy new parts after explaining why the hallway smells like burnt plastic. Hey, wait a second, you have a custom part! Yes, yes I do. It is a part I made to help simplify the wiring on my automated bartender, drinktendr . It is designed to have a single power cord in, the positive wires go to the relay and back again, and have proper power cords go back out to the target device. You can wire this up without the board; it just will be a bit messier. If you want to get the boards created, the file for the PCB is in Codeplex in the source code area in the Files directory. Pictures should help I think the two primary areas that will help show the who/what/when/where/why/how are overviews of the top and of the cannon mountings. Chassis Cannon Body Top Why doesn’t mine look good yet?!?! It takes time to get all the mountings and wiring installed correctly. We had to demo to the Gu using a robot that had wires all over the place! It wasn’t pretty, but the key thing is that it got the job done. Only after I got the functionality working did I shorten wires and do some cord clean-up. I stated this above, but I’ll reiterate the fact, that having longer wires helped me move stuff around while being able to adapt to new layouts. Conclusion Building two Betties was a fun and hard project. By leveraging past projects, we completed the project quickly without compromising functionality. In upcoming articles, we’ll talk about how to program Betty, as well as how to get the phone to talk to her. Also, if I missed a section of building out Betty that you want me to cover, please comment and I’ll happily explain more of what I did. About The Author Clint runs Coding4Fun and is on the Channel 9 team at Microsoft. Clint has yet to have a project he can’t catch on fire J. If you need to get a hold of Clint, his email is clint.rutkas@microsoft.com, his personal blog is at http://www.betterthaneveryone.com and his twitter account is @ClintRutkas. t with a pressurized co2 tank and armed t-shirt cannons running wild. This article won’t really talk about code, since that is a different, upcoming article; rather, this article will explain how to build the physical robot, code-named Betty. To find out about the Windows Phone 7 application, code-named Frank, wait for the next article. Clint Rutkas - Microsoft Coding4Fun Ninja Source Code: Download Difficulty: Software Medium - Hardware Advanced Time Required: 2 weeks Software Needed: Visual C# 2010 Express, Visual Studio Phone Developer Express Hardware: Servo City Pan-Tilt, Robot Marketplace battlebot kit, Phidget 0/0/4 Relay board, Phidget Advance Servo controller, t-shirt cannons, nuts and bolts, polycarbonate, and a lot of coffee / soda. WARNING: This project deals with voltages and amperages that could hurt you and your electronics. Use voltmeters and common sense before randomly connecting and touching wires. In this multipart article series, we’ll cover: Project overview Developing the phone application Building the robot Creating the phone user experience Part 9c into Part 143B? What? For a project like this, there are no real instructions. It is a custom project. If I was asked to build another one, chances are it would look different. I spent a lot of time drawing out and talking to people, figuring out how to get all the parts to play nicely. Only then did I go down to my local plastics place (I recommend TAPs Plastic in Seattle) to give them a technical drawing of what I wanted. The parts will vary depending on the look / feel you want. I wish I could give you part drawings that you could replicate, but I don’t think they would do you much good. What I will do, however, is give you a ton of pictures, which should point you in the right direction. Research and development Typically, I research parts and features to death. However, due to the two-week time constraint of being ready for the Mix conference, I went with what I knew worked for my previous projects while focusing on how to make Betty self-contained since requiring Betty to be plugged in would defeat the purpose of having her be a robot. The design of Betty was broken down into a few key parts: driving, aiming, shooting, brains, and power. Primary part list: 1x – Battlekit medium kit with stock batteries 1x – Cisco Linksys gigabit wireless router 1x – 13” HP Envy laptop 1x – Phidget 0/0/4 Relay board 1x – Phidget Advanced Servo Controller 1x – Servo City Pan-Tilt 985 series 2x – Burst 175 T-Shirt cannons (with electronic solenoid values) 2x – Odyssey PC680MJ 12V 17AH Batteries 2x – Castle BECs (set to 6V) (Battery Elimination Circuit) 1x – Castle Pro BECs (set to 12V, has two outputs) 1x – 10lb CO2 tank 1x – Pressure valve (Able to adjust to 300 PSI) 1x – Serial port to USB Adapter Driving a robot Without knowing the weight of certain parts, I had to choose a base that could handle the load and be big enough to support everything I loaded onto Betty. From building random, previous robots, I knew of a company, Robot Marketplace, with a ton of internet parts, including full bodies. I decided a medium version complete with stock batteries and motors would fit my needs. The batteries are configured here in series to boost the voltage from 12volt to 24volt. The kit comes with an AmpFlow motor controller, which is actually a rebranded Roboteq controller. This connects to the computer via a serial to USB adapter. You’ll also have to get the Roboteq software to configure the motor controller to work off RS232 (Serial Port). Shooting and aiming a t-shirt cannon The cannons are Burst 175 T-Shirt cannons with electronic solenoid valves, allowing them to be fired with the Phidget 0/0/4 Relay board. The cannons are mounted onto a Servo City Pan-Tilt which is controlled by a Phidget Advanced Servo Controller. The pressure on the robot is fixed. Having a brain and communicating Since Dan and myself had features in the initial planning that could require heavy processing, we decided it was best to have a laptop control everything, though initially, ideas of using the .Net Micro-framework were put out there as well. We decided on a 13” HP Envy to be the brains of the operation. One thing we loved about this laptop is the extended battery, which snaps onto the bottom to give it a 14-hour life! We used a Linksys wireless router for getting the phone and the laptop to be able to talk to one another. For the keynote, we had to leverage a wired connection, but we’ll typically use a wireless connection between Betty and Frank. Powering everything The battlebot kit comes with batteries to power the motors, but we still needed to power everything else. I went with 2 massive 12volt 17-amp hour batteries, which just barely fit the case, and I wired them in series to boost the voltage. This would give me the massive amount of energy needed to power all of the random electronics. Since nothing on this robot, other than the motors, runs at 24v, we adjusted the voltage. This is where the BEC (Battery Elimination Circuit) came into play. Here is the breakdown: If you use different parts, you’ll have to pay attention to the voltages. This is one reason why I like the Castle BEC units, I could just alter the voltage instead of buying a new BEC. I also highly recommend installing on/off switches. If you plug stuff in with this type of voltage, you’ll get sparks, which carbonize the plugs. Building knowledge brain dump To mount the top of the robot to the chassis, I had to get a drill press and drill the sidewall of the front and back plate. I decided to save some money and buy a low-end drill press for this, but having a higher end drill press would have made my life a bit less stressful. Drilling it had 1/16th of an inch on either side to punch through. After drilling, I used a 10-24 tap to put in screw threads so I could use thumbscrews to mount the two together. The two plates were T-6 aluminum, so I used WD-40 to help lubricate both drilling and tapping. If you’ve never tapped a hole before, make sure you go a half turn in and then a quarter turn out. This helps break up the little bits of metal in the hole and so helps prevent the tap from breaking. One thing to be aware of is the movement of the Pan-Tilt and how this relates to mounting the cannons. We had programmatic stops so the cannons didn’t go too far up or down or rip out any cords by rotating too much. Another helpful tip is to use extra wire so you can move stuff around. Then, once you figure out final layout, either trim the extra wire or install entirely new wiring. My final tip, and the tip to follow if you only follow one, is the following: use a Voltmeter before you connect anything together. I failed to follow this advice and had two wires switched, which reversed the polarity of the power. When I turned it on, I had a nice electrical fire break out, which destroyed 3 BECs. This was a hundred dollar mistake, which took a half-day to repair, and it could have been far worse. Verifying and re-verifying the voltage will not only keep you safe, it will keep you from having to buy new parts after explaining why the hallway smells like burnt plastic. Hey, wait a second, you have a custom part! Yes, yes I do. It is a part I made to help simplify the wiring on my automated bartender, drinktendr . It is designed to have a single power cord in, the positive wires go to the relay and back again, and have proper power cords go back out to the target device. You can wire this up without the board; it just will be a bit messier. If you want to get the boards created, the file for the PCB is in Codeplex in the source code area in the Files directory. Pictures should help I think the two primary areas that will help show the who/what/when/where/why/how are overviews of the top and of the cannon mountings. Chassis Cannon Body Top Why doesn’t mine look good yet?!?! It takes time to get all the mountings and wiring installed correctly. We had to demo to the Gu using a robot that had wires all over the place! It wasn’t pretty, but the key thing is that it got the job done. Only after I got the functionality working did I shorten wires and do some cord clean-up. I stated this above, but I’ll reiterate the fact, that having longer wires helped me move stuff around while being able to adapt to new layouts. Conclusion Building two Betties was a fun and hard project. By leveraging past projects, we completed the project quickly without compromising functionality. In upcoming articles, we’ll talk about how to program Betty, as well as how to get the phone to talk to her. Also, if I missed a section of building out Betty that you want me to cover, please comment and I’ll happily explain more of what I did. About The Author Clint runs Coding4Fun and is on the Channel 9 team at Microsoft. Clint has yet to have a project he can’t catch on fire J. If you need to get a hold of Clint, his email is clint.rutkas@microsoft.com, his personal blog is at http://www.betterthaneveryone.com and his twitter account is @ClintRutkas. en Tue, 21 May 2013 12:05:45 GMT Tue, 21 May 2013 12:05:45 GMT Rev9 Re: Coding4Fun Cannon – Building the Robot Just Awesome! I'm loving it

posted by vinay

]]> http://channel9.msdn.com/coding4fun/articles/Coding4Fun-Cannon--Building-the-Robot#c634202064000000000 Thu, 16 Sep 2010 04:00:00 GMT http://channel9.msdn.com/coding4fun/articles/Coding4Fun-Cannon--Building-the-Robot#c634202064000000000 vinay Re: Coding4Fun Cannon – Building the Robot Woooo...!!! i will try it....for fun...

posted by Sachin

]]> http://channel9.msdn.com/coding4fun/articles/Coding4Fun-Cannon--Building-the-Robot#c634225392000000000 Wed, 13 Oct 2010 04:00:00 GMT http://channel9.msdn.com/coding4fun/articles/Coding4Fun-Cannon--Building-the-Robot#c634225392000000000 Sachin